产品详情
| 品牌 | 品名 | 产品型号 | 订货号 |
| NI | 模块 | SCXI-1102 | |
| 产地 | 可售卖地 | 是否进口 | 保修期 |
| 美国 | 全国、国外 | 是 | 一年 |
| 发货地点 | 发货方式 | 使用方式 | 适用行业 |
| 厦门 | 顺丰快递 | 调试安装 | 电厂钢厂水泥厂船舶造纸 |
| 服务优势 | 国外进口 、 备货供应、 | 价格合适、品质可靠 | 订货 |
| 产品特点 | 一手货源、 按型号供货 | 售后有保障 | 何经理180,5988-4797 |
这镍SCXI-1102(零件号:776572-02，183087H-01)是一个32通道电压输入模块可以完成冷结传感器的硬件扫描。该模块为每个通道提供2 Hz低通滤波。该模块具有42 V过压保护、2 Hz带宽和333 kS/s最大采样速率。由于该模块的带宽为2 Hz，改变增益后，用户必须等待约3秒才能获得精确的测量结果。这SCXI-1102电压输入模块非常适合高精度热电偶测量。该模块可获得毫伏、伏特、0至20毫安和4至0毫安的电流输入信号。这镍SCXI-1102当SCXI-1581发送激励时，模块也可以从RTD获得信号。
这SCXI 1102可与SCXI-1300、SCXI-1303、SCXI-1308、SCXI-1310、TC-2095、TBX-1303或TBX-96接线板一起使用。建议使用SCXI-1303等等温接线盒进行精密热电偶测量。操作所需的其他项目NI SCIXI 1102电压输入模块包括:用户应用所需的SCXI机箱或PXI/SCXI组合机箱、SCXI-1600或E/M系列DAQ设备、计算机(如果使用SCXI机箱)、电缆、电缆适配器和传感器。可以使用NI-DAQmx驱动软件和其他应用开发环境(ade)在设备上开发应用，如LabVIEW、LabWindows/CVI或Measurement Studio。
有线模块上的背面信号连接器是DAQ设备和SCXI机箱中的模块之间的接口。CH 0用于差分多路传输32个通道、CJ传感器和从模块到链接的DAQ设备的模拟信号。如果SCXI-1102模块链接有DAQ设备，则数字线路不可用于通用数字I/o。NI设备配有一个96针凸DIN C前连接器和一个50针凸带状电缆后连接器。DC耦合装置重24.6盎司。，尺寸为1.2 x 6.8 x 8.0英寸。在物理维度上。它的推荐工作温度范围为0至50°c。
SCXI-1102B
The NI SCXI-1102 (Part Number: 776572-02, 183087H-01) is a 32-Channel Voltage Input Module that can complete hardware scanning of cold-junction sensors. This module has 2 Hz lowpass filtering for each channel. This module has overvoltage protection to ±42 V, 2 Hz bandwidth, and 333 kS/s maximum sampling rate. Since this module has a 2 Hz bandwidth, after altering the gains, the user must wait about 3 seconds to obtain a precise measurement. The SCXI-1102 Voltage Input Module is ideal for high-accuracy thermocouple measurements. This module can obtain millivolt, volt, 0 to 20 mA, and 4 to 0 mA current input signals. The NI SCXI-1102 module can obtain signals from RTDs as well when the SCXI-1581 delivers excitation.
The SCXI 1102 can be used with the SCXI-1300, SCXI-1303, SCXI-1308, SCXI-1310, TC-2095, TBX-1303, or TBX-96 terminal block. An isothermal terminal block such as the SCXI-1303 is suggested for precise thermocouple measurements. Other items required to operate the NI SCIXI 1102 Voltage Input Module include: an SCXI chassis or PXI/SCXI combination chassis, the SCXI-1600 or E/M Series DAQ Device, a computer (if using an SCXI chassis), cabling, cable adapter, and sensors as needed for the user’s application. Applications can be developed on the device using the NI-DAQmx driver software and other application development environments (ADEs) like LabVIEW, LabWindows/CVI, or Measurement Studio.
The back signal connector on the cabled module is the interface between the DAQ device and the modules in the SCXI chassis. CH 0 is employed to differentially multiplex the 32 channels, the CJ sensor, and analog signals from the modules to the linked DAQ device. If the SCXI-1102 module has a DAQ device linked to it, then the digital lines are not available for general-purpose digital I/O. The NI device is equipped with a 96-pin male DIN C front connector and a 50-pin male ribbon cable rear connector. The DC coupled device weighs 24.6 oz., and measures 1.2 x 6.8 x 8.0 in. in physical dimensions. It has a recommended operating temperature range of 0 to 50 °C.
