IC695PNC001-BCBC PROFINET控制器模块 通过PROFINET网络发送和接收数据

IC695PNC001是PROFINET控制器模块。该模块以前由GE智能平台公司(GE IP)生产，现在由艾默生自动化公司生产。该PROFINET控制器使RX3i CPU能够通过PROFINET网络发送和接收数据。

IC695PNC001兼容PACSystem RX3i CPU315或CPU320，固件版本为7.0及以上。该模块带有两(2)个RJ-45和两(2)个SFP插槽，SFP连接器单独出售。这些PROFINET端口只能分配一个IP地址。最多4个IC695PNC001可以安装在单个CPU上，并且只能安装在CPU所在的主机架上。多达六十四(64)个I/O设备可以连接到一个(1)控制器;每个网络128个I/O设备，分布在8个I/O控制器中。此外，在单个网络中最多可以安装8个I/O设备。该模块具有1 ms, 2 ms, 4 ms, 8 ms, 16 ms, 32 ms, 64 ms, 128 ms, 256 ms和512 ms的可配置数据更新时间。

IC695PNC001可以在电源下插拔(RIUP)。不安装SFP光模块时，占用机箱单个槽位，最大电流为0.5 a;安装2个SFP光模块时，最大电流为1.2 a，其中一个SFP光模块的电流为0.35 a。在5.5 VDC时，模块最大输出1.5 A。

除了嵌入式双PROFINET端口，该模块还配备了一个微型USB连接器，用于使用命令行接口与计算机通信。它必须在0-60摄氏度的温度范围内工作。

IC695PNC001AF

The IC695PNC001 is a PROFINET controller module. This module is manufactured previously by GE Intelligent Platforms (GE IP), now by Emerson Automation. This PROFINET controller enables an RX3i CPU to send and receive data over PROFINET network.

The IC695PNC001 is compatible for use with PACSystem RX3i CPU315 or CPU320, with firmware version 7.0 or higher. This module comes with Two (2) RJ-45 and Two (2) SFP slots with SFP connectors separately sold. Only One IP address is assigned for these PROFINET ports. Up to Four (4) IC695PNC001 can be installed along a single CPU and must located to the to the main rack only, where the CPU resides. Up to Sixty-Four (64) I/O devices can be connected to One (1) controller; 128 I/O device per network, distributed among Eight (8) I/O controllers. Additionally, up to Eight (8) I/O devices can be installed in a single network. This module has configurable data update times of 1 ms, 2 ms, 4 ms, 8 ms, 16 ms, 32 ms, 64 ms, 128 ms, 256 ms and 512 ms.

The IC695PNC001 can be Removed and Inserted Under Power (RIUP). It occupies a single slot of the chassis and draws 0.5 A without SFP devices installed and maximum of 1.2 A maximum with Two (2) SFP devices installed where an SFP device uses 0.35 A. At 5.5 VDC, the module draws 1.5 A, maximum.

Aside from the embedded dual PROFINET ports, this module also comes with a micro USB connector that is used for communicating with a computer using Command Line Interface. It must be operated at a temperature range of 0-60 Degree Celsius.